Comments on: Redsail X700 100W Laser Cutter

By: samir

samir — Fri, 26 Jan 2024 07:54:06 +0000

Firmware V.L007.075 do you have anyone from you this version i can’t found anywhere to donwload

By: Richard Labelle

Richard Labelle — Tue, 11 Apr 2017 19:32:00 +0000

https://uploads.disquscdn.com/images/f7204c5ed7697033e1e10b35452479e35815f22600d98d8550cf5393a8c708e0.jpg https://uploads.disquscdn.com/images/54e5c0cc91e382750e17218ff9a7636d82dc86bea8bda6b0deb14d0c41b3751a.jpg https://uploads.disquscdn.com/images/7cdd02396a1379562c4bf5b67057b66960fd2e6b4c743ca47db112fb0f0f898a.jpg https://uploads.disquscdn.com/images/b7a79603bd920c2c59c36151197f335d9bbb15a3a44242f67df9798c750d84a3.jpg https://uploads.disquscdn.com/images/97969c0e05a4c8ad74169b01f61269c9fae563761b0422c47b9fbb94be7b8190.jpg https://uploads.disquscdn.com/images/7a824a768af0a7b7f4623872bb88eda8e51bba887ec7b5debd69dbd2e8e2531d.jpg

By: Richard Labelle

Richard Labelle — Tue, 11 Apr 2017 15:57:00 +0000

In reply to Dwayne.

The last photo shows the connector diagram with H1 (Red & Black) wire and H=
2 (Yellow & Brown) & H3 (Blue & White).
Thanks Dwayne for getting back to me.
Rick:)
I’m having a problem loading the photos Dwayne can you send me your e-mail address.

By: Dwayne

Dwayne — Tue, 11 Apr 2017 15:21:00 +0000

In reply to Richard Labelle.

Im just gunna say one word….Chinese

But on a serious note, can u post a pic or diagram? Piggy backing steppers is usually possible. Just have to sort out wire assigment.

By: Dwayne

Dwayne — Tue, 11 Apr 2017 15:18:00 +0000

In reply to Richard Labelle.

I tried to chase it back, but got lost very quickly! These references also do not match anything on the controller from what I can tell. (The pic is of the inside of the water sensor connector.) https://uploads.disquscdn.com/images/a299c9b29e1b803815dce93d8394b14746e91cbad08d55fc0f0affaa32dce0d1.jpg

By: Richard Labelle

Richard Labelle — Fri, 31 Mar 2017 21:44:00 +0000

Hi Dwayne I’ve got another problem the Rotary Device I got has a Nema 23 motor with a 6 into 3 wire connector and the Y-axis motor I’m trying to piggy back onto has 4 wires that connect to the Y motor driver. I should have bought the laser with all the accessories to begin with. You’d think the manufacture would pre-wire the connections for all the accessories one might buy in the future.

By: Richard Labelle

Richard Labelle — Tue, 21 Mar 2017 08:59:00 +0000

In reply to Dwayne. Hi Dwayne thanks for getting back to me I would be grateful if you could trace those wires for me. Rick:)

By: Dwayne

Dwayne — Tue, 21 Mar 2017 00:02:00 +0000

In reply to Richard Labelle. Hi Rich, Are you talking about the alarm/shutdown for water flow? At present I have not connected it up. My laser however does have a plug for the flow meter with a pair of wires hooked up. I can trace these back for you if you would like? This cutter also uses the 403CB board so it should be the same.

By: Richard Labelle

Richard Labelle — Tue, 14 Mar 2017 19:47:00 +0000

Hi Dwayne I just bought a new X700 with LT-403CB control board from another guy. The problem is that the guy didn’t order any options with it and the schematic that came with the CW-5200 chiller I purchased afterwards doesn’t match any of the connectors on the control board. The chiller schematic shows H1, H2 & H3 can you tell me which terminals on your board you have them hook up to, I would really appreciate it, I don’t understand why RedSail doesn’t pre-wire the laser for their options. Rick:)

By: Andrew Spurgeon

Andrew Spurgeon — Sun, 29 May 2016 10:15:00 +0000

In reply to Dwayne.

I do. I figured a way around it in Autolaser but suspect it’s not the way it should be done. It’d be great to have a chat sometime. My email is apspurgeon@gmail.com if you’re open a kiwi giving you a shout sometime :o)